Deutsch 3-Pin Flange Connector kit, 14-16 AWG, Pins & Seals Crimp Terminals

Description

DEUTSCH 3-Pin Connector Housing Kit, Crimp Terminals, 14-16 AWG
Overview Deutsch DT Series of environmentally-sealed, connectors are designed speci cally for cable to cable applications on the engine or transmission, under the hood, on the chassis or in the cab. Where signal level circuits in harsh environmental conditions, where even a small degradation in connection may be critical, the Deutsch DT Series general purpose connectors will provide the reliability and performance at the lowest cost.
Thermoplastic (-55
0
C to + 125
0
C rated) housings and silicone seals are used to allow the connector to withstand conditions of extreme temperature and moisture. The connector may be employed with either solid-copper crimp type contacts for critical circuits or budget-minded stamped and formed contacts. In either selection, the spring action is designed in the socket and shrouded by a stainless steel hood that provides closed entry for positive axial alignment during mating, and eliminates probe damage from occurring. Contact insertion and withdrawal require no special tools and are retained in locked position by dielectic ngers, molded as an integral part of the housing. Secondary locks are assembled at the mating interfaces. If by chance the secondary locks are not properly seated during assembly, they will be pressed into locked position during the mating of the connector.
Key & Feature:
Temperature:
Operating at temperatures -55°C to +125°C
Durability:
No electrical or mechanical defects after 100 cycles of engagement and disengagement.
Vibration:
No unlocking or unmating and exhibits no mechanical or physical damage after sinusoidal vibration levels of 20 G’s at 10 to 2000 Hz in each of the three mutually perpendicular planes. No electrical discontinuities longer than 1 microsecond.
Fluid Resistance:
Connectors show no damage when exposed to most uids used in industrial applications.
Insulation Resistance:
1000 megohms minimum at 25°C.
Immersion:
IP68 rating
Moisture Resistance:
No cracking, chipping or leaking after 20 test cycles from -55°C to +125°C.
Dielectric Withstanding
Voltage:
Current leakage less than 2 milliamps at 1500 volts AC.
Thermal Cycle:
No cracking, chipping or leaking after 20 test cycles from -55°C to +125°C
.
Grommet:
Silicone rubber
Insert Retainer:
Thermoplastic
Receptacle Interfacial Seal:
Silicone rubber
Shell:
Thermoplastic
Wedgelocks:
Thermoplastic
Item Specification:
Housing Made out of Polyamide (PA)
Accepts contact size 16 (13 amps)
2 Pins arrangements, Inline mounting.
Integrated latch for mating
Wedgelocks con rm contact alignment and retention
Product speci cation document: 108-151009
Contact is Stamped form
Contact Material Copper Alloy
Wire Insulation O.D Range: .095 - .150 (2.41 - 3.81)
Air Size
14-18 AWG
(2.0 - .75)
RECOMMENDED STRIP LENGTH INCHES (mm) .150 - .200 (3.81 - 5.08)
Thermoplastic (-55
0
C to + 125
0
C rated)
What's is included:
1x (3 pin) Deutsch Male Connector
( Flange Mounting )
1x  (3 pin) Dectsch Female Connector
1x Wedge for Lock Female
1x Wedge for Lock Male
3x Male Crimp Type
Terminals ( Stamped Contact in Strip Packaging )
3x Female Crimp Type
Terminals ( Stamped Contact in Strip Packaging )
Benefit of Strip/Packaging of Terminals
Strip/Reel Packaging Contacts have an easier time handling the terminals while they are attached to the strip. Whenever yours hand are steady or not then maybe this will make things easier for you.
Specification
Male & Female Pins
Material - Metal
Copper Alloy
Material - Plating Mating
Tin over Nickel
Material - Plating Termination
Tin Over Nickel
Operate Temp Min
-55°C
Operate Temp Max
125°C
Termination Interface: Style
Crimp or Compression
Wire Insulation Diameter
0.095" - 0.15" (2.41-3.81mm)
Wire Size AWG
14, 16, 18